The WIP thread

For questions/topics that don't fit into the other, more specific forums.
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

The WIP thread

Post by PaulT »

Figured I'd keep these in the one thread rather than start a new one for every single knife that takes shape!

Here are two that I've had lying around for a while but aren't for anyone in particular so they aren't moving along very fast. The suji is clad white #1 that I forged out as the billet wasn't quite as tall as I wanted. The petty is RWL34 that's entirely stock removal.
Suji_petty.jpg
J david
Posts: 1109
Joined: Sun Jan 29, 2017 5:07 pm
Been thanked: 5 times

Re: The WIP thread

Post by J david »

The profile on the petty is very nice. What is the length?
Georgek
Posts: 707
Joined: Thu Jan 26, 2017 9:01 pm
Location: NY

Re: The WIP thread

Post by Georgek »

Beauties !
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

J david wrote: Wed Jun 28, 2017 6:08 pm The profile on the petty is very nice. What is the length?
Petty is 150mm.
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

Some pics of a handle install, glueing everything together and then polishing. I've wondered for a while what a Kramer was like to use, so I figured I'd make one. Of course I have no idea what the grind is like, but I was able to copy the profile. Probably a little taller than I'd like to be honest. Incidentally the petty above snapped at the tang when I was trying to straighten it out since it warped a little in HT. This is the main reason I have a HT oven on the way.
G1.jpg
G2.jpg
G3.jpg
G4.jpg
G5.jpg
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

Just heat treated this one today. I tried putting some clay on the spine for a hamon and I'll be honest, I'm quite relieved that it made it through the quench at all. I've made about half a dozen knives now while attempting differential hardening and half of them have cracked. Unfortunately a good hamon seems to need a water quench and from what I've heard, a high failure rate is not unexpected.

It's taken a slight upwards curve, which is natural for any differential hardening. It isn't really visible in the pic so I set a ruler on the spine, you can see it's probably less than 1mm but I'll take that out as you can see it in person. I'll get to grinding it and hopefully I'll get a nice hamon from it!
IMG_1885.JPG
IMG_1884.JPG
milkbaby
Posts: 594
Joined: Sun Jan 29, 2017 11:12 am
Location: Sunny Florida
Been thanked: 2 times

Re: The WIP thread

Post by milkbaby »

Looks like good potential for a really nice hamon! :thumbsup:

Outta curiosity, which steel is this? Couldn't you get a hamon with a fast enough oil quench if it's an oil hardening steel? I think aogami is mizu honyaki tho Japanese kitchen knife makers seem to go for much more subdued hamon than most western makers...
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

Steel is 1080, so it can go either way on quenchant. Kevin Cashen recommends a fast oil on anything less than 1/4" thick. I'm still playing around with quenching oils, we don't have Parks 50 available to us here in the UK which is obviously a favourite of many bladesmiths. There are a couple of alternatives but water seems to be the standard for a nice active hamon. I did try and minimise the possibility of cracking on this one by doing an interrupted quench, 3 seconds in water that had been warmed to 120°F, then out and into some canola oil (not the best, but all I had on hand).

We'll see how things look when I get a bit more grinding done!
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

Here's some grinding on the last one. Been hard at work on other stuff so knives have suffered a little bit.
IMG_0110.jpg
nevrknow
Posts: 658
Joined: Thu Apr 06, 2017 1:53 pm
Location: Aiken, SC
Has thanked: 10 times
Been thanked: 11 times

Re: The WIP thread

Post by nevrknow »

Nice looking blade!
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

Here it is again, taken to 120 grit, few more grits to go.
IMG_1939.JPG
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

Here's some progress pics of the above knife, lots of hand sanding and polishing to this point.

Hand sanding up to 2500 grit
IMG_2019.JPG
Polished
IMG_2018.JPG
And finally etched
IMG_2020.JPG
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

Couple more of the same knife. Hamon came out pretty nicely, I'm going to leave it here. Not sure on handle, I'm thinking something fancy to go with the relatively plain blade. Thoughts?
IMG_2027.JPG
IMG_2028.JPG
milkbaby
Posts: 594
Joined: Sun Jan 29, 2017 11:12 am
Location: Sunny Florida
Been thanked: 2 times

Re: The WIP thread

Post by milkbaby »

Looking nice...

How fancy are you going for? I vote for fossilized mammoth tooth with meteorite bolsters! :)
jmcnelly85
Posts: 2657
Joined: Thu Jan 26, 2017 8:59 pm
Has thanked: 24 times
Been thanked: 414 times

Re: The WIP thread

Post by jmcnelly85 »

That thing looks like a workhorse, I'd keep it simple and utilitarian. Something like g-10 or other bulletproof material. A fancy handle would be like wearing vintage Jordan's and a nirvana t shirt.
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

Working on some outdoor knives today as they’re quicker than kitchen knives! First is a hunter ready for HT, second is a smallish Bowie that I’ve forged out from a bar
BD286EA9-5519-452D-9065-921B950AE86C.jpeg
D48000BC-CD81-4339-8F84-CAAB19135BD3.jpeg
E15E90E5-2113-474F-9653-5EB0A3D81378.jpeg
95071717-3A83-424B-A7FB-1C07A64C241F.jpeg
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

Back to work this week after some time away from anvil and forge. Been finishing this up, as well as finishing another skinning knife for someone.
C5829E5F-9625-482C-97C5-70E6183EB98E.jpeg
684281EE-CA09-4640-97E0-A73ADC8770AB.jpeg
Finished skinner
2C2D5AEE-D7A4-429E-BB6E-68D48AE16D14.jpeg
ButlerHoosierChef
Posts: 722
Joined: Tue Oct 31, 2017 9:34 pm
Location: Greenfield Indiana
Has thanked: 68 times
Been thanked: 31 times

Re: The WIP thread

Post by ButlerHoosierChef »

Keep up the good work! Hope you can make some kitchen knives soon! Love what you have done!
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

Been a long time away! I've been away from knifemaking for a little bit but am now getting back to it. These aren't really WIP pics so much as fully finished beauty shots, but why not come back with a bang? Both available, I'll post up details soon with extra pics.

Carbon feather, 240mm
feather1.jpg
Stainless raindrop, 225mm
raindrop1.JPG
PaulT
Posts: 57
Joined: Mon Jun 26, 2017 11:31 am

Re: The WIP thread

Post by PaulT »

Three new ones, all stainless RWL34. I really like this steel, it's pretty easy to grind even once hardened and it gets crazy sharp pretty easily. There's a 225mm gyuto, 150mm nakiri, and a 120mm petty. The nakiri is a little shorter than average but I didn't have as much of the bar left as I thought after cutting out the gyuto. The square nose of a nakiri seemed a little easier to work with that trying to make anything else, plus I've never made a nakiri before so it should be a fun learning experience.
IMG_0391.jpg
Post Reply